新疆昌吉州医疗卫生机构消毒质量检测分析

来源 :地方病通报 | 被引量 : 0次 | 上传用户:juk3donda
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
目的了解掌握新疆昌吉回族自治州(昌吉州)医疗卫生机构消毒工作质量,为不断提高全州医疗卫生机构消毒工作质量和医院感染控制工作提供科学依据。方法对2007~2009年全州医疗卫生机构检测资料进行回顾性分析。结果 2007~2009年全州7县市各类医疗卫生机构消毒质量采样检测1985份,合格1732份,平均合格率为87.25%;3年检测结果比较,差异有统计学意义(χ2=59.75,P<0.005),2009年最高为92.76%,2007年最低为78.98%;不同项目检测合格率比较,物体表面检测合格率最高为99.32%,污水合格率最低为55%;不同类别医疗卫生机构相同项目检测结果比较,州直和县级综合医院最高为96.61%,个体医院最低为90.29%。结论 2007~2009年昌吉州医疗卫生机构消毒工作质量呈逐年提升趋势,但诸多方面仍存在薄弱环节,需进一步加强院内消毒质量管理工作,将医院感染控制在较低水平。 Objective To understand the quality of disinfection of medical and health institutions in Changji Hui Autonomous Prefecture of Changji, Xinjiang, and to provide a scientific basis for continuously improving the quality of disinfection and hospital infection control in Quanzhou medical and health institutions. Methods Retrospective analysis of the detection data of Quanzhou medical and health institutions from 2007 to 2009 was conducted. Results From 2007 to 2009, all the medical and health institutions in 7 counties and cities in the whole country were sampled and disinfected in 1985, with a pass rate of 1725. The average pass rate was 87.25%. The results of 3-year test showed that the difference was statistically significant (χ2 = 59.75, P <0.005), the highest in 2009 was 92.76%, and the lowest in 2007 was 78.98%. The passing rate of different projects was 99.32% and the lowest passing rate of sewage was 55%. The same items in different types of medical and health institutions The test results showed that the highest state-level and county-level general hospitals was 96.61%, the lowest for individual hospitals was 90.29%. Conclusion From 2007 to 2009, the quality of disinfection in medical and health institutions in Changji prefecture has been increasing year by year. However, there are still some weak points in many aspects. It is necessary to further strengthen the disinfection quality management in hospitals and control the infection in hospitals to a relatively low level.
其他文献
采用电阻点焊对400MPa级超细晶粒钢进行焊接,研究了工艺参数对接头组织和性能的影响。结果表明,其接头HAZ组织由贝氏体、马氏体及M-A组元等淬硬组织组成,而熔合区组织由粗大
封面设计是书籍装帧设计的首要环节。封面上的内容包括书名、编著者名、出版社名等文字以及装饰形象、色彩、构图等,要求既能体现书的内容、性质与体裁,又能给读者以美的感受。本文以《中国酒文化》封面设计为实例,介绍了如何利用Photoshop强大的图层功能和灵活多变的工具进行构图,将不同的素材同构,以达到书籍封面设计的艺术性要求。1图层功能在封面设计中的应用技巧一幅Photoshop制作的作品往往是由多个图
期刊
本文介绍了实时内核的中断机制,研究了μC/OS-Ⅲ为缩短中断关闭时间做出的改进.通过对比μC/OS-Ⅱ以及μC/OS-Ⅲ的中断管理办法,分析μC/OS-Ⅲ在哪些方面作出了改进.这些改进
采用真空扩散连接工艺对Cu/Al异种材料进行连接,焊后利用扫描电镜和EDS对焊接接头的微观组织及元素扩散行为进行了研究。在焊接温度为540℃、扩散时间为60 min、焊接压力为5M
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
业界极具可扩展性的飞思卡尔i.MX6系列应用处理器现已批量供货,为各种快速增长的应用实现新的嵌入式性能和能效水平奠定了基础.rn飞思卡尔i.MX 6系列集成1个、2个或4个ARM Co
农业,离不开种子,这是众所周知的。无论是传统意义上的农业,还是当下已经形成生产规模、占据了主流地位的现代农业,种子都是生产流程中的关键要素。从当前全球农业的发展状况
广州致远电子股份有限公司二十年来一直专注于嵌入式仿真器和在线编程工具的研究,旗下的TKScope嵌入式智能仿真开发平台是一款专业的仿真和在线编程工具.多年来,TKScope一直
由于双相钢电阻点焊过程中的快速冷却,熔核区易形成脆硬马氏体,在进行力学性能评价时会出现焊点界面撕裂等问题.为此,本文以1.4mm双相钢(DP600)为研究对象,研究了点焊过程保