【摘 要】
：
Micro heat pipe (MHP) is applied to implement the efficient heat transfer of light emitting diode (LED) device. The fabrication of MHP is based on micro-electro-mechanical-system (MEMS) technique, 15 micro grooves were etched on one side of silicon (Si) s
【机 构】
：
KeyLaboratoryforMicro/NanoTechnologyandSystemofLiaoningProvince,DalianUniversityofTechnology,Dalian1
【出 处】
：
OptoelectronicsLetters
论文部分内容阅读
Micro heat pipe (MHP) is applied to implement the efficient heat transfer of light emitting diode (LED) device. The fabrication of MHP is based on micro-electro-mechanical-system (MEMS) technique, 15 micro grooves were etched on one side of silicon (Si) substrate, which was then packaged with aluminum heat sink to form an MHP. On the other side of Si substrate, three LED chips were fixed by die bonding. Then experiments were performed to study the thermal performance of this LED device. The results show that the LED device with higher filling ratio is better when the input power is 1.0 W; with the increase of input power, the optimum filling ratio changes from 30% to 48%, and the time reaching stable state is reduced; when the input power is equal to 2.5 W, only the LED device with filling ratio of 48% can work normally. So integrating MHP into high-power LED device can implement the effective control of junction temperature.
其他文献
半导体激光器侧面抽运的内腔倍频激光器是实现高功率、高稳定且低成本连续绿光激光器的有效方式。抗灰迹KTP晶体(GTR-KTP)适用于高功率连续激光倍频，其抗光伤阈值优于普通的KTP晶体，倍频转换效率高。使用该晶体能够避免普通KTP晶体在高功率激光应用中受到“灰迹”效应等严重影响。使用GTR-KTP成功研制了一台高效高功率侧面抽运腔内倍频连续绿光激光器。采用优化的平-凹-平三镜折叠腔结构，掺钕的钇铝石榴石(NdYAG)激光晶体，Ⅱ类相位匹配GTR-KTP晶体内腔倍频，当808 nm抽运功率约为180 W时，得
当与若丹明6G染料激光辐射(λ=568.6亳微米）参量混频时，获得氦氖激光红外辐射(λ=1.15微米)在铊蒸气中转换成紫外波段(λ=377.6毫微米)。利用了具有禁戒跃迁6Ρ1/2-7Ρ3/2的泵浦的双光子共振，和转换辐射频率趋近于7Ρ3/2-7S1/2跃迁频率。
A new tunable microwave photonic notch filter with negative coefficients is presented. It is based on a polarization modulator and a polarization beam interferometer. Experimental results are presented that embody the new concept.
针对短波射频信号光纤传输需求，设计了一种64路信号光纤传输方案，采用射频信号数字化变换技术和数据光传输技术，实现1~30 MHz短波信号高性能传输，同时还设计了同步时钟传输分配电路，保证传输的射频信号幅度、相位技术指标的实现。经系统指标测试，射频信号幅度一致性≤0.2 dB，相位一致性≤0.5 o。技术指标完全满足设计要求。
亚稳态氦激光雷达通过发射调谐至亚稳态氦原子的1 083.0 nm共振线的激光来探测热层和外逸层的亚稳态氦原子数密度。能够覆盖的探测范围约为200~1 000 km。在这个高度范围内，亚稳态原子密度较小，随着季节的变化，数密度最大通常不超过1 cm-3。中国科学技术大学目前正在研制基于六个1 m口径望远镜阵列和高能量1 083 nm脉冲激光器的亚稳态氦共振荧光激光雷达。雷达的望远镜有效面积约4.8 m2；1 083 nm脉冲激光器采用光参量震荡(OPO)和光参量放大(OPA)技术，以532 nm高能量脉冲作
The influence of the refractive index n2 of optical cement on the structure angle, field angle, and transmission of Glan-Thompson prism has been studied in detail. The results show that the structure angle will increase with the decrease of n2 under the c
量子效率是电荷耦合器件(CCD)最主要的参数之一，针对目前CCD器件量子效率定标需求，提出了一种均匀光辐射法测量CCD器件量子效率方法，并对系统的不确定度进行了评定，得到系统的扩展不确定度为3.6%。同时选用CCD器件对系统扩展不确定度进行验证。实验结果表明，在300~1100 nm波长范围内，选用的三个波长点最大的重复性为0.42%，因此说明系统的不确定度分析是合理的。该系统完全可以满足目前CCD器件量子效率测量需求,对生产厂家及使用单位具有重要的使用意义。
介绍了436～490nm波段的激光染料(BzOE)2P系列的光谱和激光特性,研究了不同取代基及溶剂对染料激光调谐性能的影响;并和香豆素47作了比较。