REMANUFACTURING相关论文
采用双目摄像机结合结构光组成主动视觉测量系统, 并与机器人耦合, 构建了一种具有视觉功能的智能激光加工机器人, 能够感知各种复......
逆向工程模型重建过程中在曲面和实体转换时常会出现曲面缝隙过大难以缝合成实体的情况, 而且不同的造型软件系统精度不同, 经常存......
机器视觉技术对激光机器人加工过程检测与控制具有主要作用。基于CCD/CMOS光电视觉技术，开展了激光再制造机器人零件三维几何形貌重......
Many original equipment manufacturers(OEMs)carry out collecting operations by themselves or a third party.Most of the ex......
把奢侈、环保偏好消费者考虑到再制造品市场需求中,研究了奢侈与环保消费者构成市场的再制造品最优定价策略,发现奢侈与环保偏好消......
在考虑产品回收再制造的闭环供应链中,原始制造商如何应对外部再制造商的竞争威胁是其面临的重要决策问题。针对由制造商和再制造......
为探究吕家坨井田地质构造格局,根据钻孔勘探资料,采用分形理论和趋势面分析方法,研究了井田7......
为探究吕家坨井田地质构造格局,根据钻孔勘探资料,采用分形理论和趋势面分析方法,研究了井田7......
The lead time compression is the core of supply chain management with time competition and the powerful source of compet......
Nano surface engineering is the new development of surface engineering, and is the typical representation that the advan......
Numerical Calculation and Experimental Research on Crack Arrest by Detour Effect and Joule Heating o
...
Failure, especially induced by cracks, usually occurred in the service process of chemical equipment, which could cause ......
Four different topics for high-temperature components, namely the development of the assessment codes for the structural......
The guide-pieces, used in the process line of steel roiling, were the important components. The guidepieces, which were ......
Remanufacturing system is a term of green system project which conforms to the national sustainable development strategy......
Sand-wear resistance of brush electroplated nanocomposite coating in oil and its application to rema
Sand-wear resistance of nano scale alumina particle reinforced nickel matrix composite coating (n-Al2O3/ Ni) prepared by......
Design and micro mechanical properties of nano-SiO2 strengthened composite coatings towards remanufa
Nano-SiO2 particles strengthened Ni-based composite coating was designed and prepared on steel substrate. The structures......
To improve the solid lubricity on the worn surface of frictional-pairs, a convenient and simple brushpainting technique ......
Remanufacturing closed-loop supply chain network design based on genetic particle swarm optimization
As the huge computation and easily trapped local optimum in remanufacturing closed-loop supply chain network (RCSCN) des......
根据消费者对新产品和再制造品的异质需求构造需求函数,研究了新产品、制造商生产的再制造品和再制造商生产的再制造品三者相互竞......
As system of a serial of technologies and engineering activities, remanufacturing aims at restoring and rebuilding waste......
This paper deals with the scanner exterior calibration algorithm when the scanner is arranged by the robot and the objec......
阐述了我国盾构机再制造的发展现状并指出了我国盾构机再制造发展的不足与挑战,综述了盾构机主轴承、刀具刀盘、液压系统、减速机......
