STAINLESS相关论文
The deformation and fracture behaviors of low-carbon steel, medium-carbon steel, and high-carbon steel were studied on i......
Niobium(V) ethoxide(Nb(OEt)5) was synthesized by electrochemical reaction of ethanol with niobium plate as the sacrifici......
This paper presents the planar Fiber Bragg Grating (FBG) hydrophone probe sens- ing principle,and theoretically and expe......
This paper seeks to optimize parameters, reduce the cost of desulphurization and the consumption of operation about KR p......
CO2 laser is employed to join a piece of powder metallurgical material (PMM) to a stainless steel in butt joint welding ......
The WC powder was precoated on the surface of CrNiMo stainless steel and then made into an alloying layer by using the l......
The developed 1Cr18Ni9Ti austenitic stainless steel containing 1.63 wt.%B have been characterized by X-ray diffraction(X......
Deeply penetrated welds can be produced with high-power-density lasers.Thus the factors affecting laser weld penetration......
In this research,aging treatments at temperatures of 800 and 900°C for different aging time of 5-60 min were conducted ......
简介本钢不锈钢冷轧连续退火酸洗线的工艺流程和设备组成及关键设备的主要性能参数。
Brief introduction Baining stainless ste......
The residual stress of T-joints for SUS304 stainless steel by YAG laser welding was measured by the method of hole-drill......
This paper discusses the application of several techniques involved in the development of the 3D finite element (FE) mod......
Tempered tool steel 5Cr15MoV was normalized at different temperatures followed by air-cooling.It is found that the hardn......
The market of stainless electric steel kettles is growing significantly, but the main mechanism for polishing kettles vi......
Most commercialized coronary stents are made of 316L stainless steels due to its good combination of properties,and curr......
The electrochemical behaviors of 2205 duplex stainless steel in NaCl solution with different temperatures and concentrat......
In this study, resistance spot weldability of 180 grade bake hardening steel (BH180), 7123 grade interstitial free steel......
In this research,stainless steel bipolar plates for proton exchange membrane fuel cell(PEMFC)have been treated by an atm......
The development of closed-loop control systems is one of the most effective ways to improve the stability of the keyhole......
Currently commercialized coronary stents are mainly made of the medical 316L stainless steel and cobalt-based alloy(L605......
Quantitative sampling,dilution and separation for high-level radiation solution must be in hot cell.Because of difficult......
基于DEFORM-3D有限元平台,建立了304不锈钢环件热辗轧的三维有限元模型。对304不锈钢热辗轧过程的宏观规律进行了模拟研究,分析了......
采用光学显微镜、扫描电镜和电子显微镜对双相不锈钢在不同热处理温度下的显微组织、力学性能、相组织转变和耐蚀性等进行了研究。......
The first wall(FW) is one of the core components in ITER. As the heat sink material,the CuCrZr alloy shall be properly j......
对奥氏体耐热不锈钢进行合理合金化,在化学成分方面进行了优化,加入了微量的稀土元素,适量的氮和硅元素。以典型钢种Therma 253MA......
通过对退火态441不锈钢进行不同温度、不同时间的时效处理,分析其不同时效处理状态下力学性能及组织的变化规律。结果显示,650~950......
不锈钢表面电镀Pd-Ni膜层在强腐蚀性溶液中对基体能起到良好保护作用,但膜层服役性能及寿命还需进一步提高。本文作者研究电流密度......
采用喷砂技术对304不锈钢板表面进行处理,并对喷砂处理后的试样进行热处理和低温固体粉末包埋渗铝处理,分析讨论了喷砂助低温渗铝......
The conventional methods of determining the dynamic resistance were mostly done by measuring the voltage and current at ......
采用热浸镀铝合金工艺在不锈钢上制备铝基隔离防护界面,再将含热浸镀铝合金层的不锈钢骨架与AZ91镁合金镶嵌铸造成形,并研究钢/铝......
Free-standing diamond films have been successfully deposited on stainless steel substrates using microwave plasma-assist......
